Double surface planer factory in China: The most common application involves gluing a coating (veneer, laminate, composite, PVC etc) onto a substratum (MDF, hardboard, plywood, hollow panels, blockwood etc). The basic configuration of the pressing line is comprised of a feed belt, an automatic press and a discharge deck. This configuration can be completed with numerous options, such as glue spreaders, polishers, automatic feeders, disk, roller or belt conveyors, automatic assembling stations, panel turners and stackers. Lines with various degrees of automation can be supplied right up to fully automatic lines that do not require direct intervention by the operator. Discover more details on double planer machine.
The compound mitre saw has become a fixture in the work shop because it is versatile and accurate. The mitre saw consists of a powerful circular saw mounted on an arm that hinges at the rear of the tool. When the blade is lowered in a chopping motion, it cuts through the work-piece, passing through a slot in the base. The motor and blade can be pivoted with respect to the base for mitre cuts. It is also possible to tilt the blade too, which is handy for cutting crown mouldings which are set at a pitched angle that must also turn around corners. The diameter of the blade determines the maximum cut width. Most models have variable speeds, but the jigsaw is designed to cut precisely not quickly. Feed the wood to the saw flush to the saw table. Jigsaw blades are thin and easily broken, so take care not to bend, twist, or put too much pressure on them. Drill holes in the waste wood at the tightest corners to help you achieve a clean and neat cut. The depth of the saw throat determines how large a piece of wood can be cut on a given saw.
A typical hydraulic down-acting press uses a pair of hydraulic cylinders, one on each end, to generate the tonnage required for the down stroke of the machine. Traditionally, these machines have a C or O frame profile design. With both types, when facing the front of the machine the hydraulic cylinders are located on the left and right hand side of the upper beam. Since the upper beam is being pushed down and up with hydraulic power, the upper beam will fall during a power outage and could create an unsafe environment. Down acting presses are commonly blocked at night to take pressure off of the hydraulic system. The lower beam does not move during bending so the operator will not get feedback that the brake is engaged.
Sanding is the operation of finishing wooden items after they have been machined. Essentially, a sanding machine performs a sand papering job to produce a uniformly sanded surface. Three common types of sanding machines are : Belt sander; Spindle sander; Disc sander. It has an endless cloth backed abrasive belt which runs over two drums and is used for sanding and shaping flat surfaces. One of the drums is rotated by an electric motor and serves as the driver, while the other supports the belt and keeps it in proper tension. For sanding work by the abrasive belt, the the workpiece is supported by an adjustable table that may be tilted to any desired angle.
The band is available in two models, vertical and horizontal. In the former, two wheels are arranged side by side and the table is mounted underneath. In the latter model, Frame illustrated in Fig. 10.55, the wheels are arranged one above the other in a vertical plane below the table and the band passes through the table. As in the case of the circular table, angular cuts are obtained by tilting the saw table. The size of the band saw is specified as the distance from the saw band to the inner side of the frame. The distance is roughly equal to the diameter of the wheels.
Modern machinery often requires pneumatic pressure, be it for saws, sanders, impact wrenches, grinders, spray guns, washers, stapling, nailing or pneumatic tooling, the compressor has become a necessity. The compressor consists of: motorised pump; tank for storing the compressed air; on/off control; regulator. There’s also a metal frame on which all the parts are mounted, usually with a carrying handle and occasionally wheels. A drill press can be used to drill round holes, sanding, grooving and mortising with the addition of specialised attachments. Discover even more details at https://www.v-holdmachinery.com/.
After 20 years development, V-HOLD has constructed strong hardware facilities and humanized management system by bringing in tens of brand-new large automotive precision CNC machine center from developed countries such as Japan, German, along with over 67,000m2 large modern workshop with complete facilities and production lines, V-HOLD has realized its high efficient production. Besides that, the cooperation with world famous management consulting firm and introduction of modern business administration system such as ERP, 6S have laid solid foundation to the development of V-HOLD. Thanks for the trust and support of our customer. V-HOLD will consistently stick to the belief that: Profession and concentration accomplish excellent brand !
